Why is my electricity bill so high? Usually for one of three reasons: the bill is based on an estimate or the wrong reading, the price you pay has gone up, or your home is genuinely using more electricity than before. Each has a different fix, so it is worth working through them in order before assuming you’ve done something wrong. Start with the bill itself, then the prices, then what is plugged in.
In short
| Check | What to look for |
|---|---|
| Is the bill estimated? | An “E” or “estimated” next to the reading |
| Is it the right meter? | Meter serial number on the bill matches the one on your meter |
| Has the price changed? | Unit rate and standing charge compared with your last bill |
| Did a fixed deal end? | You may have rolled onto a standard variable tariff |
| Economy 7 set up correctly? | Day and night readings not swapped |
| New or faulty appliances? | Heaters, tumble dryers, hot tubs, old fridges |
| Season | Winter heating, lighting and drying use more |
1. Check whether the bill is estimated
If you don’t send readings and don’t have a smart meter working in smart mode, your supplier estimates your use. Citizens Advice points out that a summer bill can be estimated from your winter use, and the reverse.
Look for an “E” or the word “estimated” next to the reading. If the estimate is too high, take a reading, send it to your supplier and ask for a corrected bill. Sending a reading every month keeps bills accurate.
The opposite also happens: if your old bills were underestimated, the first real reading in a while produces a large catch-up bill. That is a correction, not a price rise.
Smart meter bills that say “estimated”
A smart meter that isn’t sending readings, for example after a change of supplier, is not working in smart mode. Your bills will then be estimated until you send readings yourself or the meter is fixed.
2. Check it is your meter
Compare the meter serial number printed on your bill with the number on your meter. In flats and converted houses, meters are sometimes mixed up, so you could be paying for a neighbour’s use. If they don’t match, contact your supplier straight away.
3. Check what you pay per unit
Your bill has two parts:
- the unit rate, in pence per kWh, which depends on how much you use;
- the standing charge, a fixed daily amount you pay even if you use nothing.
Compare both with your previous bill. The Ofgem price cap sets the maximum unit rate and standing charge on standard variable tariffs and changes every three months. It is not a cap on your total bill.
According to Compare the Market, the cap was set at £1,723 a year on average for a typical household paying by direct debit for October to December 2026, up 4% on the previous period. Standing charges and rates also vary by region and payment method.
If you were on a fixed tariff that has ended, you will usually have moved onto the supplier’s standard variable tariff. Check your end date and compare deals.
4. Check your Economy 7 set-up
Economy 7 and similar tariffs charge less at night and more during the day. The Centre for Sustainable Energy suggests two checks:
- Do you actually use enough at night? These tariffs suit homes with night storage heaters or a hot water tank heated overnight. Without them, the higher day rate can cost you more.
- Are the two readings the right way round? If day use is billed at the night rate and night use at the day rate, bills can be very high. Boil a kettle during the day and see which register moves fast: that’s your day reading.
Also check that storage heaters and the immersion heater are timed to run on the cheap hours.
5. Test for a faulty meter
Switch off everything you can, including the immersion heater and heating, and leave the fridge and freezer closed. Note the reading, wait a couple of hours and read it again. If the numbers still climb noticeably with almost nothing on, report it to your supplier, who will arrange a check.
6. Look at what is using the electricity
Appliances that make heat use the most: electric heaters and fires, immersion heaters, electric showers, tumble dryers, hot tubs, and fish or reptile tanks. An old or faulty fridge or freezer can also run far longer than it should.
To estimate any appliance, use:
watts ÷ 1,000 × hours of use = kWh
Then multiply by your unit rate from the bill. Two illustrations:
- a 2 kW plug-in heater used 4 hours a day uses 2 × 4 = 8 kWh a day, or around 240 kWh a month;
- a tumble dryer using about 4 kWh a cycle, run five times a week, uses around 80 kWh a month.
A new heater or dryer, someone working from home, or an electric car charging at home can explain a jump on its own. A smart meter’s in-home display or app shows your use by the half hour, which makes it easier to spot what drives it.
7. Remember the season
Winter bills are higher: longer heating hours if you heat electrically, more lighting, more drying indoors. Compare with the same months last year rather than with the summer.
If the bill is still wrong
- Contact your supplier with readings, photos of the meter and your bill.
- Back-billing rules: you generally can’t be charged for energy used more than 12 months before if the supplier didn’t bill you correctly for it, under Ofgem rules.
- Complain using the supplier’s complaints process.
- Go to the Energy Ombudsman if you can’t reach an agreement. It is independent and free to use.
If you are struggling to pay, tell your supplier: under Ofgem rules they must offer support, such as an affordable payment plan. Citizens Advice can also help.
To cut use rather than price, see how to bleed a radiator if you have wet heating, and solar battery storage if you have panels. More guides are in the Energy section.
